Wheelchair accessible home lift
The pneumatic vacuum elevator PVE52 model is specially designed for people with
reduced mobility. This model pneumatic vacuum elevator allows the possibility of transporting a passenger in
The vacuum elevator PVE52 has an exterior diameter of 1.36 cm and accommodates up to three people (238 kg). Available in two, three and four stops (max. height 10.5m ) it is ideal for those who want a spacious and panoramic residential elevator in their home.
There are many wheelchair home lifts, but only our pneumatic vacuum elevator PVE52 gives you the space and security you need with a spectacular design. The exterior cylinder of the biggest of our vacuum elevators is made of aluminum and transparent polycarbonate. It is also the only model with stainless steel interior cabin. A perfect finish!
The vacuum elevator greatly reduces energy costs and maintenance, as our pneumatic vacuum elevator works without pulleys or pistons. This allows for low energy consumption during ascent and zero during descent. The pneumatic vacuum elevators are econfriendly elevators.
External cylinder diameter: 52 11/16” (1,316mm)
Rated Load: 525 lbs. (238 kg)
Speed: 20 fpm (.10 ms)
No pit required. Bottom level floor must be 100% level as elevator rests on existing floor.
No hoistway required.
Standard Unit (turbine motors located on top): 107” (2,719mm)
Split Unit (turbine motors located remotely): 97” (2,464mm)
Penetration required to install through floors and ceilings: 54 11/16” (1,389mm)
220V, 60/50 Hz, 35amp single phase power supply
6 turbine motors located in pump box using a total of 6KW
Entrance width opening: 32” (813mm)
Internal cabin height: 79” (2007mm)
Internal cabin diameter: 44” (1,118mm)
Automatic LED lighting and cabin fan
Door openings: same side (in-line) and walk through (180º).
All doors are hinged on top left, with door swing to the left, from inside
Door Height: 79 . ” (2,026mm)
Height to top of Door closer: 81 .” ( 2,071mm)
Each landing level specified will include only one door.
24 Volt electrical circuits with all controls in cabin
Push button call controls with precise leveling at each landing.
Automatic descent to ground level at safety speed in the event of a power failure.
Mechanical emergency brakes within two inches of freefall in vacuum loss
or catastrophic failure.
Electromechanical interlocks at each landing
Minimum height required at the ground floor is 92” (2,34 m).
Minimum required height at the upper floor is 107” (2,70 m).
Diameter of finished through floor hole must be 5411/16” (1,46m).
When installing a three or four floor elevator, all openings circular
perforations should be perfectly aligned.
The electric feed shall be 220VAC single phase through an independent line
of conductors of AWG N° 10 (6mm ); there shall be ground connection and a thermo-magnetic switch
of 35A to be used exclusively for the elevator. The electrical supply is to be near the head
(elevator’s top portion) and it is required to leave the female electrical receptacle at the top
center of the elevator.
220VAC (no exceptions 220VAC must be provided, 210VAC or 230VAC is not
acceptable, if installation does not have 220VAC on a regular basis, a voltage regulator or
transformer must be installed by home owner). Voltage fluctuations are not covere by the
If installing a phone line a phone jack is to be provided near the power
supply, but isolated.
It is strongly recommended that a Buck Boost or voltage stabilizer be
installed along with the electrical work to prevent any damage to electrical components due to
When installing the elevator, consider the total dimensions, as a small
room will generate a higher noise level. Therefore, it is not advisable to install the split
motor in a very small facility.
There must be an opening to make way for the cylinders of 54 11/16” (1,39
m) in diameter and of 92” (2,34 m) in length down to the ground floor. This access may be
through door or window openings.
Install a hook to bear 800kg at the ceiling where the elevator is to be
installed to lift the cylinders. If it is impossible to install this hook, the minimum height at
the last level shall be at least 109” (2,75 m).
In no case must the perforation of the ceiling be less than 2” (5cm) from
the wall, in order to allow for the installation tripod.
All requirements for the split unit model (remote location of head unit) are
the same as the standard model except for the following…
Minimum required height at the upper floor is 97” (2,47 m).
Required space for remote location of head unit in attic or adjacent
closet is 39” L x 25” W x 26” H (0,84m x 0,45m x 0,68m)
Remote location of head unit can be accommodated up to 30 linear feet (10
m) away from the elevator.
Split unit connections require two 4” (10cm) PVC pipes to run the distance
from the top of the upper floor cylinder split plate to the remote location of the head
Air supply to split unit has to be drawn from interior of residence
(proper housing of head unit and air duct to interior of home required)
Electrical power supply to be provided within direct access to remote
location of head unit.
Please submit your quote form
If you are looking for additional information or to find the contact information of your local dealer, please fill out our quick contact
PVE offers a variety of three residential elevator models: PVE30, PVE37, and PVE52
Contact us and tell us which pneumatic lift model is best for your size or
functionality and how many stops / doors you would need. Our commercial technical team will be happy to
you and get in touch with our nearest authorized installer distributor.